Units | M1022 | ||||
Worktable size (L * W) | mm | 540×250 | |||
Max. travel of table (L * W) | mm | 560×260 | |||
Table T slot (slot number x slot width) | mm | 1×14 | |||
The grinding wheel size (o. d * w * i. d.) | mm | ?200×20×?31.75 | |||
Distance spindle center line to working table | mm | 420 | |||
Grinding wheel speed | 50HZ | r/min | 2850 | ||
60HZ | r/min | 3360 | |||
The vertical (up and down) feed handwheel feed | Handwheel per turn | mm | 1.25 | ||
Handwheel per lattice | mm | 0.01 | |||
Transverse (front and rear) feed handwheel feed | Handwheel per turn | mm | 4 | ||
Handwheel per lattice | mm | 0.02 | |||
Spindle motor | kw | 1.5 | |||
Cooling motor | W | 40 | |||
The process surface of the base level of the parallel degree | mm | 00:00.0 | |||
Surface roughness | ?m | Ra0.32 | |||
Net weight | kg | 850 | |||
Gross weight | kg | 950 | |||
mm | 1680x1140x1760 | ||||
mm | 1200x1400x1940 |
Units | MY1224 | |||
Worktable size (L * W) | mm | 600×300 | ||
Max. travel of table | mm | 630×320 | ||
Table T slot (slot number x slot width) | mm | 1×14 | ||
The grinding wheel size (o. d * w * i. d.) | mm | ?300×30×?76.2 | ||
Distance spindle center line to working table | mm | 520 | ||
Grinding wheel speed | 50HZ | r/min | 1450 | |
60HZ | r/min | 1680 | ||
Table longitudinal (left and right) speed | m/min | 3-20 | ||
Table transverse (front and rear) feed handwheel feed | Continuous (stepless) | mm/min | 600 | |
Intermittent (stepless) | mm/times | 0-6 | ||
Handwheel per turn | mm | 4 | ||
Handwheel per lattice | mm | 0.02 | ||
The vertical (up and down) feed handwheel feed | Handwheel per turn | mm | 2 | |
Handwheel per lattice | mm | 0.01 | ||
Hydraulic motor | kw | 2.2 | ||
working pressure | Mpa | 2.2 | ||
Fuel tank capacity | L | 4 | ||
Maximum flow rate | L/min | 100 | ||
Spindle motor | kw | 20 | ||
Cooling motor | W | 2.2 | ||
The process surface of the base level of the parallel degree | mm | 40 | ||
Surface roughness | ?m | 120 | ||
Net weight | kg | 1400 | ||
Gross weight | kg | 1530 |
Units | MY1230 | |||
Worktable size (L * W) | mm | 750×300 | ||
Max. travel of table | mm | 780×320 | ||
Table T slot (slot number x slot width) | mm | 1×14 | ||
The grinding wheel size (o. d * w * i. d.) | mm | ?300×30×?76.2 | ||
Distance spindle center line to working table | mm | 520 | ||
Grinding wheel speed | 50HZ | r/min | 1450 | |
60HZ | r/min | 1680 | ||
Table longitudinal (left and right) speed | m/min | 3-20 | ||
Table transverse (front and rear) feed handwheel feed | Continuous (stepless) | mm/min | 600 | |
Intermittent (stepless) | mm/times | 0-6 | ||
Handwheel per turn | mm | 4 | ||
Handwheel per lattice | mm | 0.02 | ||
The vertical (up and down) feed handwheel feed | Handwheel per turn | mm | 2 | |
Handwheel per lattice | mm | 0.01 | ||
Hydraulic motor | kw | 2.2 | ||
working pressure | Mpa | 2.2 | ||
Fuel tank capacity | L | 4 | ||
Maximum flow rate | L/min | 100 | ||
Spindle motor | kw | 20 | ||
Cooling motor | W | 2.2 | ||
The process surface of the base level of the parallel degree | mm | 40 | ||
Surface roughness | ?m | 120 | ||
Net weight | kg | 1400 | ||
Gross weight | kg | 1530 |
MY4080 | ||
Table Size (L× W) | mm | 800*400 |
Max movement of working table(L× W) | mm | 900*480 |
T-Slot(numberx width) | mm | 3x 14 |
Max distance from spindle center to table surface | mm | 600 |
Wheel Size(Outer diameterx widthx Inner diameter) | mm | ?355x 40x ?127 |
Wheel speed | r/min | 1450 |
1680 | ||
Longitudinal speed of working table | m/min | 3-25 |
Cross feed(front and rear) on handwheel | mm/min | 600 |
mm/times | 0-8 | |
mm | 5 | |
mm | 0.02 | |
Vertical(up and down) feed on handwheel | mm | 0.8(1.0) |
mm | 0.01 | |
Speed of vertical feed | mm/min | 500 |
Spindle motor | Kw*p | 4*4 |
Coolant pump motor | W | 125 |
Lifting motor | W | 180 |
Hydraulic motor | kw | 2.2*6 |
The parallelism of working surface to base level | mm | 00:00.0 |
Surface roughness | ?m | Ra0.4 |
Net | kg | 2800 |
3200 | ||
Gross | ||
mm | 2550*2000*2100 |